Page 1 of 2

*** Polish translation - Polskie tłumaczenie

Posted: Mon Feb 12, 2007 3:43 pm
by Skiff
I know that in XnView already is polish translation but it is old (for 1.90.1) so not all the strings are translated.

So I've made my own using Restorator

P.S. Is there posibility to get english version of dll? (or even those strings in english because for good translation it would be more convienient - xnview.exe is protected, so I can't get the resource for translation)

Requested…

Posted: Mon Feb 12, 2007 4:31 pm
by Clo
:) Hello !
…P.S. Is there possibility to get english version of dll?…
Officially, not yet, although this has been suggested IN THIS THREAD, and largely supported as a temporary ease…
Pierre promised to do the text-files for the 2.0 version, so all these issues will be solved… :D
- Support welcome, of course…
…xnview.exe is protected, so I can't get the resource for translation…
• The EXE is Aspack compressed… :wink:

:mrgreen: Kind regards,
Claude
Clo

Re: Polish translation

Posted: Mon Feb 12, 2007 7:19 pm
by xnview
Skiff wrote:I know that in XnView already is polish translation but it is old (for 1.90.1) so not all the strings are translated.

So I've made my own using Restorator:
http://skiff_spolszczenia.republika.pl/files/xnviewpl.zip

P.S. Is there posibility to get english version of dll? (or even those strings in english because for good translation it would be more convienient - xnview.exe is protected, so I can't get the resource for translation)
Please contact me by PM or email, and i'll send you the text files

Re: Polish translation

Posted: Wed Feb 14, 2007 12:57 pm
by Anon
Skiff wrote:P.S. Is there posibility to get english version of dll? (or even those strings in english because for good translation it would be more convienient - xnview.exe is protected, so I can't get the resource for translation)
As for as I've looked at it, both unpacking exe and creating English dll shouldn't be a problem.

Re: Polish translation

Posted: Wed Feb 14, 2007 7:32 pm
by helmut
Anon wrote:
Skiff wrote:P.S. Is there posibility to get english version of dll? (or even those strings in english because for good translation it would be more convienient - xnview.exe is protected, so I can't get the resource for translation)
As for as I've looked at it, both unpacking exe and creating English dll shouldn't be a problem.
Translating/hacking the DLLs is a solution for one single version of XnView and/or testing purposes, but this is not recommended and what we want, here. Please wait till Pierre sends you the appropriate text files for translation.

Thank you in advance for your efforts in translating to Polish!

Posted: Sun Feb 18, 2007 11:31 am
by Skiff
Polish translation for 1.90.3 is ready. Link on PM.

Posted: Sun Feb 18, 2007 3:48 pm
by xnview
Skiff wrote:Polish translation for 1.90.3 is ready. Link on PM.
I have no PM, do you want to translate text files?

Posted: Sun Feb 18, 2007 9:06 pm
by Skiff
Oh sorry. I have sent it to Clo.

Clo's Mail Service

Posted: Sun Feb 18, 2007 9:17 pm
by Clo
:) No problem, I will resend it to Pierre immediately… :D

:mrgreen: KR
Claude
Clo

Posted: Mon Feb 19, 2007 7:29 am
by xnview
Skiff wrote:Oh sorry. I have sent it to Clo.
But it's better to translate the 2 text files, your translation will be lost for next release.... :-(

Posted: Mon Feb 19, 2007 4:32 pm
by Skiff
xnview wrote:But it's better to translate the 2 text files, your translation will be lost for next release.... :-(
What do you mean? If there is something else to translate send it to me.

Posted: Mon Feb 19, 2007 5:59 pm
by helmut
O.k., again in bold and firered:

Translating/hacking the DLLs is a solution for one single version of XnView and/or testing purposes, but this is not recommended and what we want, here. Please wait till Pierre sends you the appropriate text files for translation.

To make a real, permanent translation Pierre has to send the translator two header files. After translation, the translator sends the header files back to Pierre for compilation into the DLL.

@Clo: When talking about translations please also tell people about the official way for translating. This will help to avoid misunderstandings in future.

Posted: Mon Feb 19, 2007 9:45 pm
by Skiff
I understand that. Note that in first post I mentioned about editing resources of dll.

After that Clo (or someone else? - I don't remember) sent me .rc files - and I thougth that this was what I should do. File in the first post is not available any more. Only those .rc files which was sent to me - not the dll with modified sources
xnview wrote:But it's better to translate the 2 text files, your translation will be lost for next release.... :-(
Yes I want to do this - but I thought I just did :/ (but I remember 3 files, 3 .rc files)

Posted: Mon Feb 19, 2007 10:06 pm
by helmut
Skiff wrote:Yes I want to do this - but I thought I just did :/
Sorry for the extra work, Skiff. :-| The correct files are named "stringpo.h" and "xnviewpo.h", where "po" is the language code of polish (you have guess it ;-) ). Pierre will send those header files to you - given that you have mailed Pierre your e-mail address (for mail address please see here).

Thank you very much for updating the Polish translation!

Posted: Tue Feb 20, 2007 6:39 am
by Skiff
helmut wrote:The correct files are named "stringpo.h" and "xnviewpo.h", where "po" is the language code of polish
Ok. I'm waiting for those header files. And the correct polish language code is pl not po :)